交底內容：
1. 綜合管溝及其附屬工程的結構砼為C30防水砼，抗?jié)B標號為S6，墊層為C15素砼。
2. 混凝土的保護層厚度：
綜合管溝及其附屬工程結構的地下結構：底板下層、壁板外側和頂板上層為50mm，其余為30mm；
綜合管溝及其附屬工程結構的地上結構：梁、柱為35mm，板為25mm；
3. 混凝土配制：本工程采用商品混凝土，混凝土配置嚴格按設計要求的技術指標確定�；炷�土配合比必須經試驗確定，水泥的選用要減小地下水對鋼筋及混凝土的腐蝕。
4. 混凝土澆注前對模板、鋼筋、預埋件、預留孔洞、止水帶等進行檢查，清除模板內雜物，隱蔽驗收合格后，方可灌注混凝土。
5. 混凝土澆注過程中隨時觀測模板、支架、鋼筋、預埋件和預留孔洞等情況，發現問題，及時處理。
6. 混凝土的澆注：本工程采用商品混凝土，并用流槽把砼從攪拌車直接卸到澆注地點。混凝土到達現場后，材料試驗員核準混凝土發車時間，混凝土的品種、強度等級，混凝土坍落度是否在規定的范圍內，并隨機取樣測定和做試塊，嚴格把好混凝土的質量關。不同的分部混凝土施工分述如下：
(1).  底板混凝土澆注：
A.  底板厚300mm，混凝土強度等級為防水C30、抗?jié)B等級為S6。在底板面以上500mm設置一水平施工縫，施工中間設鍍鋅鋼板止水帶，截面為300mm×3mm。
B.  在混凝土澆筑前24小時內對墊層進行灑水濕潤，采用“一個坡度、分層澆筑、循序推進、一次到頂”的斜面分層法澆筑。
C.  每個施工段均選擇沿管溝方向澆筑，逐層覆蓋沿管溝方向推進。澆筑混凝土?xí)r保證每個工作面各有一個流槽�；炷�土澆注要連續，一氣呵成，不留任何豎向施工冷縫。
D.  澆筑混凝土?xí)r邊澆筑邊振搗，振動器插入方式可采用行列式或
Cards on the table contents:
1. Combined duct and its subsidiary structure of the project for the C30 concrete waterproofing concrete, impermeability grade for the S6, bedding factors for the C15 concrete.
2. Concrete cover thickness:
Combined duct and its subsidiary structure of the underground structure works: the lower floor, wall and roof lateral upper 50mm, the rest is 30mm;
Combined duct and its subsidiary engineering structures on the ground structure: beam, column for the 35mm, plate is 25mm;
3. Concrete Mixing: This project uses concrete, concrete configuration in strict accordance with the technical specifications to determine design requirements. Concrete mix to be determined by experiment, to reduce groundwater use cement and concrete on the steel corrosion.
4. Template before pouring concrete, steel, embedded parts, aside holes, water stop, etc. to inspect, remove the template debris, hidden acceptance only after the concrete pouring.
5. Concrete pouring at any time during the observation template, frame, steel, embedded parts, and set aside holes, etc., identify problems and timely treatment.
6. Concrete pouring: The project uses concrete, and concrete with a groove to direct discharge from the mixer to the pouring site. Concrete arrived at the scene, materials testing staff approved the departure time of concrete, concrete variety, intensity level, whether concrete slump within the limits prescribed, and do random sample testing and test block, a strict standard of concrete quality. Different segments of concrete construction are as follows:
(1). Bottom Pouring Concrete:
A. floor thickness 300mm, waterproof concrete strength grade C30, impermeability grade S6. 500mm above the floor surface to set a level of construction joints, the middle set galvanized steel water stop construction, the section is 300mm × 3mm.
B. 24 hours before pouring the concrete within the wet cushion for watering, using "a slope, hierarchical placement, sequential forward, once up to the ceiling" of the slope stratification placement.
C. Construction segment were chosen for each trench along the direction of casting, layer by layer along the trench direction of forward cover. When pouring concrete to ensure a flow of each face in each slot. Concrete pouring to be continuous, coherent, do not leave any vertical construction cold joints.
D. pouring concrete when pouring side edge vibration, vibrator insertion can be carried determinant or
 

前往下載