交底內容：
預制混凝土板塊和水泥方磚路面鋪設施工
1  范圍
    本工藝標準適用于工業與民用建筑的廠區、庭院道路及停車場等，鋪設預制混凝土板塊和水泥方格磚面層。
2  施工準備
    2.1  材料及主要機具：
    2.1.1  預制混凝土板塊：強度不應小于20MPa，規格為49.5cm×49.5cm，路面塊材厚度為10cm以上，人行道及庭院塊材厚度為5cm以上。進場時應有出廠合格證、混凝土強度試壓記錄。并對混凝土板塊進行外觀檢查，表面要求密實，無麻面、裂紋和脫皮，邊角方正，無扭曲、缺角、掉邊。板塊允許偏差：長、寬±2.5mm.，厚度±2.5mm，長度≥400mm平整度為lmm，長度≥800mm，平整度為2mm。
    2.1.2  水泥方格磚：尺寸為25cm×25cm×5cm，抗壓、抗折強度符合設計要求，其規格、品種按設計要求選配，外觀邊角整齊方正，表面光滑、平整，無扭曲、缺角、掉邊現象，進場時應有出廠合格證。
    2.1.3  砂：粗砂、中砂。
    2.1.4  水泥：325號以上普通硅酸鹽水泥或礦渣硅酸鹽水泥，有出廠合格證。
    2.1.5  磨細生石灰粉：提前48h熟化后再用。
    2.1.6  預制混凝土與路牙子，按圖紙尺寸及強度等級提前預制加工。
    2.1.7  主要機具：小水桶、半截桶、掃帚、平鐵鍬、鐵抹子、大木杠、小木杠、篩子、窗紗篩子、噴壺、錘子、橡皮錘、鏨子、溜子、板塊夾具、扁擔、手推車等。
    2.2  作業條件：
    2.2.1  庭院或小區的地下各種管道，如污水、雨水、電纜、煤氣等均施工完，并經檢查驗收。
    2.2.2  庭院或小區的場地已進行基本平整，障礙物已清除出場。
    2.2.3  庭院或小區道路已放線且已抄平，標高、尺寸已按設計要求確定好。路基基土已碾壓密實，密實度符合設計要求，并已經進行質量檢查驗收。
3  操作工藝
Cards on the table contents:
Precast concrete blocks and cement cubes laying construction
1 Scope
    This technology is applicable to industrial and civil construction plant, roads and parking lot garden, laying pre-cast concrete blocks and cement tile surface layer of the box.
2 construction preparation
    2.1 Materials and main equipment:
    2.1.1 Precast Concrete blocks: strength of not less than 20MPa, specifications for the 49.5cm × 49.5cm, 10cm road block material thickness above the sidewalk and the courtyard bulk thickness of more than 5cm. Approach should have factory certification, pressure test records of concrete strength. And the appearance of concrete blocks to check dense surface required, no anesthesia face, cracks and peeling, edges Founder, no distortion, chipping, out side. Plate tolerance: length, width ± 2.5mm., Thickness ± 2.5mm, length ≥ 400mm flatness is lmm, length ≥ 800mm, flatness is 2mm.
    2.1.2 Cement brick box: size of 25cm × 25cm × 5cm, compressive and flexural strength design requirements, specifications, design requirements according to variety selection, Founder and tidy appearance of the corners, smooth surface, no distortion, missing corner, out side of the phenomenon, there should be entering the factory certification.
    2.1.3 Sand: coarse sand, medium sand.
    2.1.4 Cement: ordinary portland cement 325 or more or slag cement, with a factory certificate.
    2.1.5 Ground quicklime powder: 48h ahead of time and then with maturation.
    2.1.6 Precast Concrete and Road teeth child, by drawing size and strength grade ahead of pre-processing.
    2.1.7 Main equipment: a small bucket, half barrels, brooms, flat shovels, iron trowel, large mugang, small mugang, sieve, sieve screens, watering can, hammer, rubber hammer, chisel, the valve plate fixture, pole, trolleys.
    2.2 Operating conditions:
    2.2.1 garden or plot of ground the various channels, such as sewage, water, cable, gas Deng Jun construction completed, and after inspection and acceptance.
    2.2.2 garden or plot of the site has a basic level, obstacles have been cleared appearance.
    2.2.3 courtyard or residential roads in actinomycetes and has been copied level, elevation, size, design requirements have been determined according to good. Compaction of subgrade soil has been compacted, compaction meets the design requirements and has the quality inspection and acceptance.
3 Operation Process
 

前往下載